Snapper ZM5201M EN User Manual

Safety Instructions & Operator’s Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 1 POWER UNIT MODELS ZM2501KH MOWER UNIT MODELS ZM

10 Section 3 - OPERATING INSTRUCTIONS 2.2 STARTING & STOPPING – ENGINE, BLADES, PARKING BRAKE This machine is equipped with dual hydrostatic wh

11 Section 3 - OPERATING INSTRUCTIONS 2.2.5. PARKING BRAKE 1. Engage parking brake by pulling the parking brake lever back to the engaged position.

12 Section 3 - OPERATING INSTRUCTIONS 2.3 CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height as desired to any position, using deck lift lever. See

13 Section 4 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the SNAPPER mower, use genuine SNAPPER replacement parts only. Contact a local

14 Section 4 - MAINTENANCE 3.2.3. CHECK MOWER DRIVE BELT 1. Foot Rest Removal a. Lower deck to lowest setting. b. Remove foot rest. See Figure 3.

15 Section 4 - MAINTENANCE 3.3.3. RIDING MOWER - LUBRICATION 1. Front Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivale

16 Section 4 - MAINTENANCE 3.5 ANNUALLY (END OF EACH SEASON) (Continued from previous Page) 3.5.2. FUEL FILTER Service fuel filter as instructed bel

17 Section 4 - MAINTENANCE 3.6 DECK REMOVAL (Continued from previous page) 4. Remove shoulder bolts, washers and nuts from rear lift arm. See Fig

18 Section 5 - ADJUSTMENTS & REPAIR DANGER Exercise EXTREME CAUTION when making this adjustment, due to close proximity of moving parts. 4.1 N

19 Section 5 - ADJUSTMENTS & REPAIR 4.2.1. MOWER DECK ADJUSTMENT (LEVELNESS) (Continued) 6. Loosen the nuts and bolts that secure both front a

IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause inj

20 Section 5 - ADJUSTMENTS & REPAIR WARNING Before attempting any adjustments, maintenance, service, or repairs, stop engine and blade, always r

21 Section 5 - ADJUSTMENTS & REPAIR 4.5.2. BLADE SHARPENING 1. Remove blade. See Figure 4.5. FIGURE 4.5 2. Inspect condition of blade.

22 Section 5 - ADJUSTMENTS & REPAIR WARNING Shield the positive terminal with terminal cover located on battery harness. This prevents metal fro

23 Section 5 - ADJUSTMENTS & REPAIR Battery Condition Chart State of Charge Syringe Hydrometer Digital Voltmeter Five Ball Hydrometer 100% Ch

24 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2.

25 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Tractor Will Not Move 1. Joystick in the neutral “N” position. 1. Place joystick in

26 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 9 X In

27 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's use, SNAPPER, through any authorized SNAPPER deal

28 PRIMARY MAINTENANCE

29 PRIMARY MAINTENANCE

3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 4. Handle fuel with extra care. Fuels are flammable and vapors are expl

30 PRIMARY MAINTENANCE

31 PRIMARY MAINTENANCE

32 NOTES

33 NOTES

34 NOTES

35 Safety Instructions & Operator’s Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 1 IMPORTANT Snapper products are built usin

4 IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE (Continued From Previous Page) 7. Disconnect battery before performing maintenance or service. Cranking

5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS...2-4 TABLE OF CONTENTS...

6 Section 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER MID MO

7 Section 2 – SAFETY MESSAGES AND SYMBOLS ENGINE CONTROLS ENGINE SPEED RABBIT “FAST” TU

8 Section 2 – SAFETY MESSAGES AND SYMBOLS HOUR METER LIGHT SWITCH BLADE SWITCH KEY SWI

9 Section 3 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.