Snapper 7-4510 User Manual download pdf

SETUP INSTRUCTIONS AND PRE-OPERATION CHECKLIST FOR

SNAPPER GROUNDS CRUISER UTILITY VEHICLE

INTRODUCTION: These instructions cover the setup of the Snapper Grounds Cruiser utility vehicle. Complete

each step carefully. A checklist has been provided. It is very important to verify and record each item on the

list prior to placing the machine into service. The dry weight of the machine you are about to setup is 1,230 lb. It

is strongly recommended that you use an overhead hoist when lifting the machine. The capacity of the device

used for lifting must exceed the weight of the machine. DO NOT work on the machine until properly blocked

and secured to prevent it from falling. If an overhead hoist is not available, you may have to remove boards

from the crate bottom to gain access with floor type jacks.

WARNING

DO NOT attempt any adjustments, maintenance or

service with the engine running. STOP engine. Set

park brake. Shift transmission to neutral and

remove key. Remove spark plug wire from spark

plug and secure wire away from spark plug. Engine

and components are HOT. Avoid serious burns,

allow all parts to cool before working on machine.

STEP 1

INSTALL REAR TIRES

The machine is securely attached to the crate bottom at

each wheel location. See Figure 1.1. The four steel

plates must be removed before lifting the machine. The

device used to lift the machine must have a capacity

greater than 1230 lb. The cargo bed is attached to the

frame of the machine with plastic straps. Carefully

remove the straps and set the cargo bed aside for

installation later.

FIGURE 1.1

1. Loosen only, two lug nuts at left and right rear

wheel hubs.

2. Remove the four bolts securing the left and right

support plates to the crate bottom.

3. Lift machine, at the rear hitch, only high enough to

allow tire installation. Block machine securely to

prevent it from falling. Remove support plates.

4. Check castle nuts to insure that the cotter pins have

been fully inserted and have at least one leg bent to

secure in place.

5. Install left and right rear tires and secure each with

5 lug nuts. NOTE: The tires are directional. Install

with valve stem out and the points of the chevron

treads pointing forward. See Figure 1.2.

FIGURE 1.2

6. Remove blocks and lower rear of machine.

7. Torque lug nuts to 75 ft-lb using sequence shown.

See Figure 1.2.

STEP 2

INSTALL FRONT BUMPER

The bolts used to attach the front bumper to the

machine are already installed in the front frame. The

bumper can be used to lift the weight of the front of the

machine. The mounting hardware must be tightened

securely (30 ft-lb).

1. Place bumper over four bolts at front of frame. Note

orientation, flat side of side plates towards bottom

2. Attach using (4) 3/8-16 flange lock nuts.

3. Torque nuts to 30 ft-lb.

INSTRUCTION No. 7-4510 (I.R. 5/3/01)

LUG NUTS

(LOOSEN ONLY)

REMOVE

POINTS OF TREADS POINTING TOWARD FRONT OF VEHICLE.

1 2 3 4 5 6

Summary of Contents

Page 1 - WARNING

1 SETUP INSTRUCTIONS AND PRE-OPERATION CHECKLIST FOR SNAPPER GROUNDS CRUISER UTILITY VEHICLE INTRODUCTION: These instructions cover the setup of the

Page 2

2 STEP 3 INSTALL FRONT TIRES The front bumper can be used to lift the front of the machine. Block the machine to prevent it from falling. NOTE: The f

Page 3

3 STEP 6 INSTALL OPERATOR PROTECTIVE STRUCTURE (OPS) The installation of the Operator Protective Structure requires two people. The mounting hardware

Page 4

4 STEP 8 (Continued) ACTIVATE BATTERY 8. Thoroughly clean any spilled acid from battery. Neutralize with Baking Soda and flush with large quantit

Page 5

5 STEP 10 (Continued) INSTALL OPERATOR’S AND PASSENGER’S SEAT FIGURE 1.7 STEP 11 ATTACH CARGO BED Attach bed to pivots at rear of frame. A

Page 6 - SNAPPER GROUNDS CRUISER

6 PRE-OPERATION CHECKLIST FOR SNAPPER GROUNDS CRUISER Snapper has completed initial adjustments and performed operational tests prior to shipping th

Comments to this Manuals

No comments

Snapper 7-4510 User Manual

Browse online or download User Manual for For the car Snapper 7-4510. Snapper 7-4510 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Snapper 7-4510